DENIOS AG Dehmer Strasse 58-66 32549 Bad Oeynhausen br>Tel.: +49 5731753-0 Email: email@example.com Internet: www.denios.ie
Fume cupboards with ejector technology or sash? The technology comparison.
In many laboratories, classic fume cupboards with front sash are used to retain hazardous vapours, gases, aerosols or dusts. In practice, however, working behind the pane often means cutting corners. Anyone who needs to procure a fume cupboard should research the alternatives. Hazardous-substances workstations with ejector technology enable barrier-free working in the laboratory - intelligent air routing and extraction replaces the front sash. In our technology comparison, we compare ejector technology with the classic fume cupboard with sash and show you which system has the edge.
Functionality of fume cupboards with sash and ejector technology
Fume cupboard with sash: Protection by safety pane
Classic fume cupboards have a suction device in the rear area, which is used to extract volatile hazardous substances such as gases, dusts or aerosols from the air. In the front area, an adjustable protective pane, the so-called sash, separates the operator from the interior of the fume cupboard. Depending on the model, the sash can be moved manually or electrically to allow access to the working area.
Fume cupboard with ejector technology: Protection through intelligent air routing
In fume cupboards with ejector technology, special nozzles on the front edge of the worktop and in the ceiling area direct air jets, so-called ejectors, specifically to the extraction strip in the rear wall. The resulting air currents propel hazardous substances such as vapours, aerosols, gases or dusts towards the rear wall, where they are safely extracted in a targeted manner. The front area is openly accessible to the operator.
Advantages and disadvantages of fume cupboard systems for the laboratory
Protection against volatile hazardous substances
Both fume cupboards with sash and fume cupboards with ejector technology offer a high level of protection against so-called volatile hazardous substances (e.g. vapours, gases, aerosols or dusts). The design of the fume cupboard according to DIN EN 14175 confirms that it meets the corresponding requirements of the laboratory guidelines and TRGS 526. In the case of a fume cupboard with sash, the effectiveness of the protection is very much reliant upon it being used correctly by each individual. To be able to work inside the fume cupboard, the sash must be opened. This should always be limited to the extent necessary for the work. The more the sash is opened, the more the retention capacity and the robustness of the fume cupboard are impaired. In practice, this can quickly lead to errors in handling the fume cupboard that impair its protective effect. In fume cupboards with ejector technology, the entire front is open throughout - but the stable air curtain, which is created by targeted blowing in the front area, ensures effective separation of the working area and the surroundings. And thus for a consistently high protection effect.
Good to know
Thanks to the flow design, which has been tried and tested over many years, the air barrier remains stable even when the employee reaches through it into the work area. Protection against physical hazards If there is a risk of hazardous substances being splashed or glass splinters flying around, only a fume cupboard with a safety pane offers you sufficient protection. The same applies to the danger of explosions. Before you buy a fume cupboard, you should take a close look at your experimental setup and consider possible physical hazards when deriving protective measures. For these applications, DENIOS offers the option of equipping the fume cupboard with ejector technology (Premium work table) with an additional hinged front panel. Individual solutions with a sash are also possible. Please contact us for more details!
Usability and efficient working
In terms of usability and efficiency, fume cupboards with ejector technology offer clear advantages over models with a sash. The further the sash of the classic fume cupboard is closed, the more it impairs the working area. In contrast, hazardous substance workplaces with ejector technology have an open front area as standard, which enables barrier-free and ergonomic working. Large containers and even bulky laboratory equipment can be brought in without any problems. In addition, with classic fume cupboards, it is essential to ensure that the sash is closed again when the work is finished. Before starting work, the sash must be correctly adjusted. These measures, which delay the work process, are not necessary with fume cupboards equipped with ejector technology instead of a sash.
Energy efficiency and sustainability
A fume cupboard with an open sash is associated with increased energy consumption. This is because the volume flow and the exhaust air volume regulation must be adjusted according to the sash position. This results in a higher exhaust air volume that must be processed via the ventilation system of the laboratory or the building. And the treatment of the air is usually expensive. A fume cupboard with ejector technology offers better energy efficiency here. Although the units perform a lot, they consume significantly lower amounts of exhaust air compared to conventional fume cupboards. You save energy, reduce your costs for filtration, cleaning and air conditioning of the exhaust air and protect the environment.
Protection against volatile hazardous substances (e.g. vapours, gases, aerosols or dusts)
+++ (if used correctly)
Protection against physical hazards (e.g. explosions, splashing hazardous substances or flying glass splinters).
+ (Models available with optional windscreen)
Usability and efficient work
Energy efficiency and sustainability
Fume cupboards with ejector technology from DENIOS
Air-conditioning work table for BECOM GmbH from Austria
BECOM GmbH from Austria manufactures electromechanical assemblies. When cleaning small parts, inflammatory acetone vapors are produced which should protect the employees. A DENIOS cleaning table with pollutant detection ensured more safety.
Mixing station in the middle of the APO GmbH production halls
The APO GmbH from Germany deals with the coating of industrial mass small parts. To protect employees against harmful coatings, DENIOS constructed a transfer and mixing station, which at the same time ensured fire-protected storage.
In the handling of chemical raw materials in the powdery or dusty state, increased safety requirements apply to the design of workplaces to protect employees. Covestro AG chose DENIOS to implement the project.
Paint mixing room in fire-rated storage container for Siemens
If working with paints and varnishes in production areas, employees have to be protected accordingly. For Industrial Turbomachinery in Sweden, Siemens needed a safe room solution for the storage and mixing of paints. In order to optimize logistical processes, the spatial proximity to other buildings should be guaranteed.
What should be considered when planning a pollutant collection system?
Sascha Mohe is a DENIOS product manager in the field of air and cleaning technology and has been involved in a number of air cleaning projects. In our expert interview, he reveals how you can combine precise protection against harmful emissions with efficient work processes.
The specialist information on this page has been compiled carefully and to the best of our knowledge and belief. Nevertheless, DENIOS Ltd cannot assume any warranty or liability of any kind, whether in contract, tort or otherwise, for the topicality, completeness and correctness either towards the reader or towards third parties. The use of the information and content for your own or third party purposes is therefore at your own risk. In any case, please observe the locally and currently applicable legislation.